KTC11: KTC1 upgraded universal pull rod linear displacement sensor
Product introduction：
KTC11 series is the company combined with more than ten years of manufacturing experience and customer feedback, by the engineering department and R & D department to optimize and improve, product appearance, internal structure, material, production process, technical parameters and sealing grade parameters have been greatly upgraded, raw materials are imported with original. Production and manufacturing fully adopt the current international industry more advanced technology and process, the product after 100 million times of reciprocating movement life test, the performance indicators and technical parameters are still in line with the industry higher standards. The signal output terminal and wire plate connection device obtained the utility model patent, and the product appearance obtained the design patent.
Scope of application：KTC11 is a general type, suitable for the position detection of various types of equipment, such as: injection molding machine, die casting machine, rubber machine, shoe machine, EVA injection molding machine, hollow bottle blowing machine, woodworking machinery, hydraulic press, etc.
Standard technical parameters：
Note: The values of linearity, service life, etc. listed in the following data table are the values of the sensor operating with the operational amplifier as the voltage output voltage to the slip brush, and
It is obtained when there is no load on the sliding brush (l e≤ 10 μA).
KTC11 Universal pull rod series | 50~110mm | 125~175mm | 200~550mm | 600~1250mm | Range selectio-n reference: unit: mm 50 75 100 110 125 130 150 175 200 225 250 275 300 325 350 360 375 400 425 450 475 500 550 600 650 700 750 800 850 900 950 1000 1150 1250
| |
Electrical parameter | Linearity（±%） | 0.1 | 0.05 | 0.05 | 0.05 | |
Resistance tolerance±10 % | 5.0KΩ | 10.0KΩ | ||||
Electrical travel | Stroke+3mm | |||||
Resolution | Infinite Unbroken analysis | |||||
Repeatability | 0.01mm | |||||
Normal working current of sliding brush | ≤10μA | |||||
A larger current that causes the brush to slip when it fails | 10mA | |||||
Max allowable operating voltage | 42V | |||||
Effective temperature coefficient ratio of output voltage to input voltage | Usually 5ppm/K | |||||
Insulation impedance( 500VDC ) | ≥10MΩ | |||||
Insulation strength（500VAC,50Hz） | ≤10 0μA | |||||
Mechanical parameterS | Shell length（A） | Stroke+78.5mm | ||||
Mechanical travel（B） | Stroke+8mm | |||||
The pull rod carries more tension | 50KG | |||||
Working force | Horizontal direction＜10N | |||||
Vertical direction≤10N | ||||||
Environmental parameter | Anti-vibration standard | 5...2000Hz , Amax=0.8mm , amax=20g | ||||
Impact resistance standard | 50g ,11ms | |||||
Operating temperature range | -60...+150℃ | |||||
Life | ＞100 x 106次 | |||||
Max operating speed | 10m/S ,Greater operating acceleration 10m/s² | |||||
IP | IP67(DIN40500/IEC529) | |||||
KTC11 Installation dimension drawing：
KTC11(LWH) installation instructions and schematic diagram：
When positioning the sensor, ensure that it is locked in the horizontal state；
The screw hole of the traction support and the sensor tie rod must be concentric；
Output type of KTC11 pull-rod resistance ruler：
Resistance output type：5kΩ，10KΩ，
Voltage output type (external/built-in module)：0-5V，0-10V，
Current output type (external/built-in module)：4-20MA (two wires，three wires），
Digital signal (external/built-in module)：RS485。
Application range of KTC11 pull-rod resistance gauge：
Application: KTC is a general type, suitable for position detection of various types of equipment, such as: injection molding machine, die casting machine, rubber machine, shoe machine, EVA injection molding machine, hollow bottle blowing machine, woodworking machinery, hydraulic press, etc.
 |  |  |  |